标准状况

参看

吉布斯能

参考资料

^NIST.NIST Standard Reference Database 7 – NIST Electron and Positron Stopping Powers of Materials Database. 1989 [08-07-25]. If you want the program to treat the material as an ideal gas, the density will be assumed given by M/V, where M is the gram molecular weight of the gas and V is the mol volume of 22414 cm at standard conditions（0 deg C and 1 atm）. 

^ISO,ISO 10780:1994 : Stationary source emissions - Measurement of velocity and volume flowrate of gas streams in ducts, 1994 

^3.03.1Robert C. Weast (Editor). Handbook of Physics and Chemistry 56th Edition. CRC Press. 1975: F201–F206. ISBN 0-87819-455-X. 引文格式1维护：冗余文本 (link)

^4.04.1"Natural gas – Standard reference conditions", ISO 13443, International Organization for Standardization, Geneva, SwitzerlandISO Standards Catalogue

^"Extraction, First Treatment and Loading of Liquid & Gaseous Fossil Fuels", Emission Inventory Guidebook B521, Activities 050201 - 050303, September 1999, European Environmental Agency, Copenhagen, DenmarkEmission Inventory Guidebook

^6.06.1"Electricity and Gas Inspection Act", SOR/86-131（defines a set of standard conditions for Imperial units and a different set for metric units）Canadian Laws

^"Standards of Performance for New Sources", 40 CFR--Protection of the Environment, Chapter I, Part 60, Section 60.2, 1990New Source Performance Standards

^"Design and Uncertainty for a PVTt Gas Flow Standard", Journal of Research of the National Institute of Standards and Technology, Vol.108, Number 1, 2003NIST Journal

^"National Primary and Secondary Ambient Air Quality Standards", 40 CFR--Protection of the Environment, Chapter I, Part 50, Section 50.3, 1998National Ambient Air Standards

^"Table of Chemical Thermodynamic Properties", National Bureau of Standards（NBS）,Journal of Physics and Chemical Reference Data, 1982, Vol. 11, Supplement 2.

^"Glossary", 2002, Compressed Air and Gas Institute, Cleveland, OH, USAGlossary

^12.012.1The SI Metric System of Units and SPE Metric Standard1984, Richardson, TX, USA（Notes for Table 2.3 on page 25 define standard cubic foot and standard cubic meter）

^"Storage and Handling of Liquefied Petroleum Gases" and "Storage and Handling of Anhydrous Ammonia", 29 CFR--Labor, Chapter XVII--Occupational Safety and Health Administration, Part 1910, Sect. 1910.110 and 1910.111, 1993Storage/Handling of LPG

^"Rule 102, Definition of Terms（Standard Conditions）", Amended December 2004, South Coast Air Quality Management District, Los Angeles, California, USASCAQMD Rule 102

^"Annual Statistical Bulletin", 2004, Editor-in-chief: Dr. Omar Ibrahim, Organization of the Petroleum Exporting Countries, Vienna, AustriaOPEC Statistical Bulletin

^"Natural Gas Annual 2004", DOE/EIA-0131（04）,December 2005, U.S. Department of Energy, Energy Information Administration, Washington, D.C., USANatural Gas Annual 2004

^Sierra Bullets L.P. Chapter 3 – Effects of Altitude and Atmospheric Conditions.Rifle and Handgun Reloading Manual, 5th Edition. "Effects of Altitude and Atmospheric Conditions", Exterior Ballistics Section, Sierra"s "Rifle and Handgun Reloading Manual, 5th Edition", Sedalia, MO, USAExterior Ballistics

^The pressure is specified as 750mmHg. However, themmHgis temperature dependant, as mercury expands as temperature goes up. Here the values for the 0-20 °C range are given.

^"Gas turbines – Procurement – Part 2: Standard reference conditions and ratings", ISO 3977-2:1997 and "Gas turbines - Acceptance tests", ISO 2314:1989, Edition 2, International Organization for Standardization, Geneva, SwitzerlandISO

^ANSI/AMCA Standard 210, "Laboratory Methods Of Testing Fans for Aerodynamic Performance Rating", as implied here:http://www.greenheck.com/pdf/centrifugal/Plug.pdfwhen accessed on October 17, 2007

^The standard is given as 29.92inHgat an unspecified temperature. This most likely corresponds to a standard pressure of 101.325 kPa, converted into ~29.921 inHg at 32 °F)

免责声明：以上内容版权归原作者所有，如有侵犯您的原创版权请告知，我们将尽快删除相关内容。感谢每一位辛勤著写的作者，感谢每一位的分享。